-
Kicker KMC5 Premium Marine Media Center (Bluetooth)
Vendor:KickerKICKER KMC5 Premium Marine Media Center Your KMC5 comes with a sunlight-viewable full color 3.5-inch LCD screen, rotary encoder and 240 watts of peak power into six channels. Add even more bump to your boat by adding amplifiers to the front, rear, subwoofer and zone-2 RCA outputs. FEATURES AT A GLANCE Charging USB w/Thumb-Drive Playback Bluetooth Connectivity Full-Color LCD Display Ability to control Zone 2 SiriusXM ready 3” Hole Cutout Dedicated Zone 2 speaker outputs NMEA Port Video RCA Input with Remote trigger wire AM/FM and Weather-band Tuner Up to 16 Favorites for each source: AM, FM and SiriusXM Front, Rear, Subwoofer and Zone-2 RCA Outputs AUX RCA Input Day/Night Mode Low Battery alert Loudness control Customizable EQ with Five Presets Voltage Display Specifications: Freq. Response - 20-20k Signal-to-Noise Ratio - 108 dB RCA Outputs - Pre-amp Outputs: Front, Rear, Subwoofer, Zone2 IP Rating - IP66 Outer Trim Ring Dimensions [in, cm] - 3.5 x 5.5, 8.89 x 13.97 Protrusion From Mounting Surface [in, cm] - 1-5/16, 3.33 Required Mounting Depth for Wiring [in, cm] - 5, 12.7 Mounting Hole Diameter [in, cm] - 2.8, 7.19 USB:Playback, Charging, Compatible File System - MP2, MP3, WMA, WAV16, FLAC, AAC, ALAC, M4A, DC 5V 1 Amp, FAT32 Bluetooth Range - 30ft Exclusive to the KMC5, the included video input can be configured in a variety of ways. Monitor your rider at the end of the rope, use it as a backup camera, even use it as a video baby monitor! The video input can be toggled with either a trigger wire or a button push. -
Kicker KMC6 Premium Marine Media Center (Bluetooth)
Vendor:KickerKICKER KMC6 Premium Marine Media Center Connect your Bluetooth to the KMC6, plug into the USB or RCA inputs, or turn on the AM/FM or satellite radio. Add a wired KRC12 Remote Commander or KRC55 Digital Remote Controller for even more control. This durable Media Center is ready for some fun on the water! (IP66) FEATURES AT A GLANCE Charging USB w/Thumb-Drive Playback Bluetooth Connectivity Full-Color LCD Display Ability to control Zone 2 SiriusXM ready 3” Hole Cutout Dedicated Zone 2 speaker outputs NMEA Port Video RCA Input with Remote trigger wire AM/FM and Weather-band Tuner Up to 16 Favorites for each source: AM, FM and SiriusXM Front, Rear, Subwoofer and Zone-2 RCA Outputs AUX RCA Input Day/Night Mode Low Battery alert Loudness control Customizable EQ with Five Presets Voltage Display Specifications: Freq. Response - 20-20k Signal-to-Noise Ratio - 108 dB RCA Outputs - Pre-amp Outputs: Front, Rear, Subwoofer, Zone2 IP Rating - IP66 Outer Trim Ring Dimensions [in, cm] - 3.5 x 5.5, 8.89 x 13.97 Protrusion From Mounting Surface [in, cm] - 1-5/16, 3.33 Mounting Depth [in, cm] - 5, 12.7 Mounting Hole Diameter [in, cm] - 3, 7.62 USB:Playback, Charging, Compatible File System - MP2, MP3, WMA, WAV16, FLAC, AAC, ALAC, M4A, DC 5V 1 Amp, FAT32 Bluetooth Range - 30ft Exclusive to the KMC6, the included video input can be configured in a variety of ways. Monitor your rider at the end of the rope, use it as a backup camera, even use it as a video baby monitor! The video input can be toggled with either a trigger wire or a button push. -
Kicker KRC12 Marine Wired Remote Commander
Vendor:KickerKICKER KRC12 Marine Wired Remote Commander Have a remote control anywhere and everywhere you want. The KRC12 remote lets you change your music with the push of a button! The KRC12 works with all current KICKER media center/radios. FEATURES AT A GLANCE Volume/Track/Station/Source Control included Mount as many KRC12s as you need, wherever you need them Fully marinized and ready for the water with an IP66 rating Easily control your sound while cruising Comes with 25’ cable Specifications: OD - 2.41" Mounting Hole Diameter - 2" Protrusion from Mounting surface: 0.75" Mounting Panel Thickness Range - 1/8"-1" Mounting Depth Minimum - 1" Included cable - 25' What's in the box: Marine digital media receiver (15A fuse) Wiring harness Rubber face-cover 2 Trim-rings (black/silver) 4 Screws Gasket Warranty/Information Card "STOP" note -
Kicker KRC55 Digital Remote Controller
Vendor:KickerKICKER KRC55 Digital Remote Controller Connect your Bluetooth to the KMC2, plug into the included USB or RCA inputs, or turn on the AM/FM radio. Add a wired KRC12 remote for even more control. This durable media center is ready for some fun on the water! Features: 2.5” (6.35cm) full-color LCD Display Controls most KMC5 functions Water-resistant IP67 rating Dimensions (in, cm) – 3 x 4, 7.62 x 10.16 Protrusion from Mount Surface (in, cm) – 11/16, 1.7 Mount Hole Diameter (in, cm) – 2, 5.11 Required Mounting Depth for Wiring (in, cm) – 1.4, 3.61 Includes snap-on trim ring (removable) Accessories: KRCEXT25 25-foot extension cable (sold separately) – connects the KRC55 to the KMC5 from a distance. KRCY1 Y-adapter splitter (sold separately) – allows you to install multiple KRC55 remotes around the craft. -
Limitless Lithium Nano HD v3 30AH, 5500-6000W Motorcycle / Pwersports w / Maintainer
Vendor:Limitless Lithium5500-6000 Watts Harley Davidson Lithium Battery With Smart Tender NANO-HDv3 ETA for Shipment July 9th to Pre-order call the shop Features Supports 5,500-6,000 watts BMS, protected motorcycle and powersports only (no vehicles with an alternator) Includes an LL3.5A-MTN (stock voltage maintainer) Max Charging: 14.8Volts 100 Warranty: Each battery comes with a 3-year manufacture defect full replacement warranty Top-mounted post and distribution block Current lead time 7-10 business days (estimated) Dimensions Size (W x D x H): 6.46” x 6.89” x 5.04” Weight: 10.36 lbs. What’s in the Box Limitless Lithium NANOHDV3/MTN -
Limitless Lithium Nano OEM Elite, 2500W Motorcycle / Pwersports
Vendor:Limitless LithiumNano OEM Elite 2500 Watts Harley Davidson Lithium Battery Nano OEM Elite Specifications Resting Voltage: 13.1V-13.4V Max Charge Voltage 14.8V Capacity: 27Ah Cranking Amps: 1380 Cold Cranking Amps: 1035 Performance RMS Wattage: 2000W Max Burst Wattage: 2500W RMS Amperage Output (Standalone for 30 seconds): 140 Amps Max Burst Amperage (Standalone for 10 seconds): 200 Amps Built-in Battery Management System (BMS) Keeps Battery Safe. The BMS in the Nano-OEM-Elite is designed to internally disconnect the battery if it rises above 15.3 or falls below 10v. This helps with cell stability and increases the batterys life. -
Limitless Nano -HD SL 12AH Motorcycle / Power sports Battery With 3.5A Battery Maintainer (BCI 20 Case)
Vendor:Limitless LithiumLimitless Lithium Nano Slim With 3.5A Battery Maintainer, 2500-3000W, 14.8V NSL-12Ah/MTN Specs Resting Voltage (Charge Voltage Dependent): 13.1V-13.4V (Temp. and S.O.C dependent) Float/Maintenance Charging Voltage: 14.2V Max Charging Voltage: 14.8V Minimum Charging Voltage: 13.6V Capacity (Ah): 12 Capacity (Pb Eq): 48 Cell Chemistry: LifePo4 Cell Life Cycles: 2,000 (80% DOD) Craking Amps (CA): 1,000 Cold Craking Amps (CCA): 750 Nominal Operating Temperature Range: Up to 140F Terminal Bolt Size: M6-100 Terminal Orientation: Positive Left Balance Board Installed: Yes Battery Management System Installed (BMS): Yes RMS Wattage (Alternator size dependent): 2,500W-3,000W (14.8V Input Voltage) Max Burst Wattage (Alternator size dependent): 3,500W (14.8V Input Voltage) RMS Amperage Output (Stand alone for 30 seconds): 200 (starting at 14.8V Max Burst Amperage Output (Stand alone for 10 seconds): 250 (Starting at 14.8V) Recommended Charging/Input Current: 75A Maximum Charging/Input Current: 100A (charging above 300A shortens the cycle life) Warranty Download -
Maestro AHD2 (PNP DSR1 Harness)
Vendor:MaestroDSR1 Plug and Play Wiring harness Wiring harness to add a DSP or DSP-based amplifier to select Harley Davidson motor cycles. This solution will reprogram the factory radio to amplified mode. How to install with DSR1 -
Maestro BHD2
Vendor:MaestroAmplifier bypass for 2014-up Harley Davidson Motorcycles with up to 4 factory amplifiers. It can be used when adding an aftermarket amplifier or installing an aftermarket radio. They are designed for CVO 14 and up. These plugs will not work on the 20 and up CVO with the Rockford Fosgate 4-channel amp in the back left bag. -
Maestro iDatalink SW Harley Davidson Radio Replacement Kit
Vendor:MaestroConnect a new car stereo and retain handlebar audio controls with a compatible aftermarket radio in select 1998-2013 Harley-Davidson models Complete kit for select Harley Davidson motorcycles. Install a new radio and retain handlebar buttons and program them to control the new radio.Includes: Maestro SW module HD1 T-harness in one package. -
Mean Machine Cycles 98-13 Road Glide Adapter Kit
Vendor:Mean Machine CyclesMean Machine Cycles 98-13 Harley Davidson Road Glide 6.5" Adapter Kit With this new Kit that Mean Machine Cycles developed, you can run almost any deep speaker in the fairing on a 98-13 Road Glide. The kit now allows those larger magnets and deeper speakers to be mounted in the fairing and clear the outer fairing.Kit comes with 5.25 to 6.5 adapters and new Hogtunes grills for the fairing, allowing you to install deeper larger speakers into the Road Glide.Custom-made parts may need some grinding and or additional parts or hardware.They have a specific side for each ring, so please look at the images here for orientation. Designed for a stock 98-13 RG inner Some modification may be required DOES NOT Work on aftermarket fairings Installation Instructions -
SaleMetra 82-9601 5.25 to 6.5 adapter rings for Harley Davidson
Vendor:Metra5.25 to 6.5 adapter rings for Harley Davidson Description Custom spacer designed for installation of 6-1/2 to 6-3/4 inch aftermarket speakers and works with all varieties of speakers including component drivers. One pair of adaptors included in each package.Sale
-
SaleCicada Audio CH8 8" Pro Coaxial Horn Speaker (Pair)
Vendor:Cicada AudioCicada Audio CH8 Pro Coaxial Horn Speaker 8" The new Cicada Audio CH8 speakers are a perfect solution for 2014 and later Harley baggers and other motorcycles. More output, lower frequency (NOT sub bass). Available in 4Ω or 2Ω …the 2Ω get more output with smaller higher efficiency / lower output amplifiers and don’t NEED a giant “current hog” for an amplifier to drive these. Specs: 500WRMS/1000 MAX Power Handling- PAIR Frequency Response: 75Hz -20Khz+/-5dB Neodymium High Energy/ Light Weight N35 Magnet structure Heavy Duty/ Die-cast Aluminum Basket 2.0” 2Ω or 4Ω – High Temp Voice Coil (Black Coat™) Voice Coil MidBass Shortening Ring for the Ultimate in speaker control 1.4” Aluminum Diaphragm High-Temp Voice Coil for Tweeter Advanced Voice Coil Heat Sink Design for Better Heat Dissipation High Sensitivity: > 99dB 1W/1M Average (1W/1M – 2.83V) 12dB Crossover with custom tooled/ Vented crossover case Can be Bi-Amped (Horn Tweeters can be run on their own dedicated channels) Total Diameter: 8.3” / 210.5mm Mounting Diameter: 7.1” / 180mm Mounting Depth: 3.6” / 91.2mm SOLD IN PAIRS Weather treated FITMENT APPLICATIONS: All Cicada Audio 8 inch and 6 X 9’s are “CUSTOM “ fitted. They do NOT drop in for an easy install (but neither does 95% of all 6 X 9’s and 100% of ALL 8 inch. These are ALL CUSTOM fitted. We recommend you find a really good motorcycle audio guy to do your install.Sale -
SaleCicada Audio CHD69HD 6X9″ Plastic Dividers for Saddle Bags (Pair)
Vendor:Cicada AudioCicada Audio CHD69HD 6X9″ Plastic Dividers for Saddle Bags CHD69HD CH/CHX series 6X9″ Plastic Dividers for Saddle Bags to be used with 8″ or 10″ Pro Midbass DriversSale -
SaleCicada Audio CHD69SD 6X9″ Silicone Dividers for Saddle Bags (Pair)
Vendor:Cicada AudioCicada Audio CHD69SD 6X9″ Silicone Dividers for Saddle Bags 6 x 9″ Silicone Bag Divider use w/ only 8″ Mid-bass Drivers. Use this divider to keep your 6 x 9″ coax or horn coax from becoming a passive radiator to the mid-bass woofer.Sale -
SaleCicada Audio CHD69TB 6x9" Tweeter Bridge (Pair)
Vendor:Cicada AudioCicada Audio CHD69TB CHD69TB 6X9″ Tweeter Bridge – PairSale
Built to Withstand the Road
DS18 speakers are designed to endure the challenges of the open road while providing exceptional sound quality. Built using durable, weatherproof materials, these speakers are engineered to resist vibrations, impacts, and exposure to the elements without compromising on audio clarity.
Effortless Integration with Your Bagger Motorcycle
Designed for seamless integration, DS18 speakers fit effortlessly into your motorcycle’s audio system without sacrificing space or style. With user-friendly installation and advanced connectivity options, including Bluetooth and RCA inputs, DS18 ensures you can upgrade your sound system without sacrificing functionality.
Customizable Sound for Every Rider
From deep bass to crisp highs, DS18 speakers offer the customization to match your audio preferences. Featuring advanced DSP (Digital Signal Processing) technology, these speakers allow you to fine-tune your sound system for an optimal listening experience. Whether you prefer a balanced sound or a bass-heavy setup, DS18 speakers deliver versatile solutions for your needs.
Shop DS18 Audio at Garage Bagger Stereo
Explore our wide selection of DS18 speakers and motorcycle audio accessories at Garage Bagger Stereo. Whether you’re looking for a minor upgrade or a complete overhaul, we are your trusted destination for premium motorcycle audio gear. With expert guidance and top-notch customer service, we ensure you find the perfect audio solution for your ride.